Skip to main content

Ixora Carrier Board

Ixora Carrier Board - Front

Ixora Carrier Board - Bottom

(Double-Click to Zoom)

Getting Started​

This section contains initial information needed to set-up the Ixora Carrier Board for the first time.

Recommendation for a first-time order​

Toradex recommends ordering the following additional products for your first-time order:

All the products can be ordered online at Toradex Webshop

Getting started for the first time?​

For detailed step-by-step instructions about how to start with both, SoM and Carrier Board, please have a look at our step-by-step Getting-Started Guide:

Product-specific information for the Ixora Carrier Board:

Having trouble?​

Please contact our technical support. Various option of technical support are mentioned in the article below.

Features​

I/O Support​

  • USB 2.0 (1x Host, 1x OTG )
  • USB 3.0 (2x Host)
  • PCIe (1x Mini PCIe)
  • I2C (2x)
  • SPI (1x)
  • UART (3x RS232)
  • PWM (4x)
  • GPIO (up to 40)
  • Analog Input (4x)
  • Ethernet (1x 10/100/1000 Mbit)
  • SATA (1x mSATA)
  • SDIO/SD/MMC (1x 4 Bit MicroSD)
  • CAN (2x)
  • LVDS (1x Dual Channel)
  • S/PDIF In/Out (1x)
  • HDMI (1x)
  • RGB (1x 24 Bit)
  • Resistive Touch (4/5-wire)
  • Capacitive Touch connector
  • Camera Parallel Interface (1x)
  • Camera Serial Interface (1x)
  • Analog Audio Line in (1x)
  • Analog Audio Mic in (1x)
  • Analog Audio Headphone out (1x)
  • RTC on Board (1x)

Block Diagram​

Datasheets​

Ixora V1.3 datasheet

Ixora V1.2 datasheet
Ixora V1.1 datasheet
Ixora V1.0 datasheet

Design Resources​

Design data Ixora Carrier Board V1.3​

Design data Ixora Carrier Board V1.2​

Design data Ixora Carrier Board V1.1​

Design data Ixora Carrier Board Archive​

Ixora Carrier Board Mechanical Models​

A basic 3D model for the Ixora Carrier Board V1.3 can be downloaded here:

Ixora Carrier Board V1.2 Models
Ixora Carrier Board V1.1 Models
Ixora Carrier Board V1.0 Models

Design and Layout Guide​

Altium Designer​

Compatible Products​

[1] For Ixora V1.0A Capacitive Touch Adapter is required, V1.1A or above are directly compatible.

Revision History​

Click to See the Product Numbering Scheme

Product Number (PID8) Format​

The format of the 8-digits Product Number (PID8) is the following:

Product Numbering Scheme

The below table describes the structure of the Product Number (PID8):

FieldDescription
PPPP4-digits number, indicating the Product Configuration (PID4) that describes the key properties of the product (e.g. Product Group, RAM capacity, etc.)
VV2-digits number, indicating the Major and Minor Version (in that order)
AA2-digits number, indicating the Assembly Variant

See the complete list of available combinations on the Revision History table of the corresponding product page.

Example​

Product number (PID8): 00291100:

0029: Apalis iMX6D 512MB
11: Major Version 1, Minor Version 1, Version V1.1 in short
00: Assembly Variant A

A specific product revision has a lifecycle defined by the product state. Learn more about it on the Product Change Notifications.

Ixora Carrier Board​

PN: 0133

Product #Product DescriptionChanges from Previous VersionRelease DatePCN Document
01331000
Ixora V1.0A
- Initial Release
2013-09-26
PCN Ixora Carrier Board V1.0A 2017-03-06
01331100
Ixora V1.1A
- Swap Apalis USBH2 with USBH3
- Use Apalis MMC1 instead of SD1
- Use new Micro SD cared holder (higher quality)
- Use SD1 pins as GPIOs to control UART2/3_RS232_FOFF#, FACTORY_DEFAULT#, PCIE_WDISABLE#_R, LED_4_RED, and LED_4_GREEN (before MMC1 pins were used)
- Add bias-circuit to the microphone input
- Connect I2C to the LVDS connector X19 to support EDID
- Add new connector X24 for capacitive touch controller support (compatibility with future Toradex display offerings)
- Add CSI connector X28
- Improve battery holder footprint
- Added footprint for recovery mode jumper JP4 (not assembled)
- Remove EEPROM (not assembled)
- Remove CAN termination resistors
- Change USB 5V regulator to supply the minimum requirement of 900mA as required by USB 3.0
- Pull-up WAKE1_MICO# to 3.3V instead of 3.3V_SW
- Increase the maximum power output (from 15W to 20W)		2017-03-24PCN Ixora Carrier Board V1.1A 2020-01-09
01331101
Ixora V1.1B
- Interim product, only for the Apalis iMX8 Early Access
- R9 changed to a 0Ω-resistor for sufficient power supply for the Apalis iMX8
2019-05-07Interim version, no PCN. For details of changes in V1.2A, see PCN of V1.1A
01331200
Ixora V1.2A
- Updated Power Supply
- EEPROM assembled by default
- New Micro USB connector
- New Ethernet connector for Industrial Temperature compliance
- New Voltage Level translator and ESD protection solution on HDMI interface
- Modified SD card circuit
- Load switch ICs added to control CAN1 and CAN2 interface power rails
- Additional capacitors C162, C163, C164, and C165 (not assembled by default) to 3.3V_PCIE1 and 3.3V_mSATA1 power rails
- Shared pads resistors connected to SD1_CD# / MXM3_190 pin to eliminate false interrupts
- Improved EMC design		2020-01-09PCN Ixora Carrier Board V1.2A 2023-01-04
01331300
Ixora V1.3A
- Replaced the MXM3 socket for the Apalis SoM edge connector
- Changed the HDMI ESD protection solution
- Replaced the CAN power switches
- Updated the USB design to meet the bulk capacitance requirements of the USB 3.1 specification
- Added support for CAN FD
- Improved the determinism of the POWER_ENABLE_MOCI signal
- Modified the value of the USB power enable signals' pull-down resistors
- Improved the ESD protection of various interfaces and features
- Replaced the RS232 transceiver with a device that is not prone to backfeeding
- Changed the HDMI connector to provide compliance with HDMI 2.0
- Changed the rail the WAKE1_MICO# signal
- Other minor changes and improvements		Q2, 2023

Errata/Known issues​

Errata Document​

Ixora Carrier Board Errata

Migration in Progress

Issue trackers are not yet available in the new developer website. See it on the archived developer website.



Send Feedback!