Skip to main content

Analogue Camera Adapter

Analog Camera Adapter

(Double-Click to Zoom)

Getting Started

Analogue Camera Adapter (ACA) is an interface board designed to easily connect the analogue cameras to the Colibri or Apalis Carrier board using Parallel Camera Interface (CIF).

The Analogue Camera Adapter accepts NTSC/PAL/SECAM standard composite video signals and converts the video signals into a YCrCb 4:2:2 video data stream that is compatible with the 8-bit ITU-R BT.656 interface standard with external HSync/VSync signals.

Up-to 4 analog cameras can be connected to the Analogue Camera Adapter V2.0.

What I need to order

Analogue Camera Adapter can be ordered with any Apalis or Colibri computer on module.

For compatible carrier boards, see the Compatible Products tab.

Where do I order

All the products can be ordered online at Toradex Webshop.

First Steps

Please read the following articles before using this product.

Having trouble?

Please contact our technical support. Various option of technical support are mentioned in the article below.

Features

Main Features

  • Uses Analog Devices, ADV7280 video decoder
  • Analogue Camera Input : 4 multiplexed video input channels, supporting NTSC / PAL / SECAM composite video signals
  • Parallel data output format: 8-Bit Parallel ITU-R BT.656 with external HSync and VSync
  • No external power supply required

Datasheets

Analogue Camera Adapter

Design Resources

Design Data for Analogue Camera Adapter

Altium Designer

Compatible Products

Further Details

  • Apalis Evaluation Board
    The ACA V2.0 connector X1 pinout is 1:1 pin mapped with respect to the the Parallel Camera Interface connector (X22) Apalis Evaluation Board
  • Ixora Carrier Board
    The Ixora Carrier Board has a 20 pin camera interface connector (X14). When the 24 way 1:1 IDC ribbon cable connector is used to connect the ACA V2.0 with the Ixora carrier board, the last four pins of the IDC cable connector are left unconnected on the Ixora carrier board side
  • Colibri Evaluation Board
    V3.2: The ACA V2.0 connector X1 pinout is 1:1 pin mapped with respect to the the Parallel Camera Interface connector (X22) on the Colibri Evaluation Board V3.2.
    V3.1 and earlier: The ACA V2.0 connector X1 pinout is not 1:1 pin mapped with respect to the the Parallel Camera Interface connector (X22) on the Colibri Evaluation board V3.1. A custom connector will be required to connect the ACA V2.0 with the Colibri Evaluation Board V3.1. For more details, please refer to the Analogue Camera Adapter V2.0 datasheet
  • Viola Carrier Board
    A custom cable will be required to interface the ACA V2.0 with the Viola Carrier Board V1.2 and Viola Plus Carrier Board V1.2. For more details, please refer to the Viola Carrier Board V1.2 datasheet

Revision History

Click to See the Product Numbering Scheme

Product Number (PID8) Format

The format of the 8-digits Product Number (PID8) is the following:

Product Numbering Scheme

The below table describes the structure of the Product Number (PID8):

FieldDescription
PPPP4-digits number, indicating the Product Configuration (PID4) that describes the key properties of the product (e.g. Product Group, RAM capacity, etc.)
VV2-digits number, indicating the Major and Minor Version (in that order)
AA2-digits number, indicating the Assembly Variant

See the complete list of available combinations on the Revision History table of the corresponding product page.

Example

Product number (PID8): 00291100:

0029: Apalis iMX6D 512MB
11: Major Version 1, Minor Version 1, Version V1.1 in short
00: Assembly Variant A

A specific product revision has a lifecycle defined by the product state. Learn more about it on the Product Change Notifications.

0119xxxx - Analogue Camera Adapter

Product #Product DescriptionChanges from Previous VersionRelease DatePCN Document
01191100
Analogue Camera Module V1.1A
Initial Release
2013-07-10
PCN Analogue Camera Module V1.1A 2016-01-08
01192000 
Analogue Camera Adapter V2.0A
- Removed Maxim IC
- Changed from Analog Devices ADV7180 to ADV7280BCPZ
- Improved signal layout
- Changed paralell pinout (8-bit data only)
2015-12-05
PCN Analog Camera Adapter V2.0A 2017-02-14
01192001 
Analogue Camera Adapter V2.0B
Correction of Errata: Series resistors have been changed in order to improve the signal quality
2017-02-14
 
01192002 
Analogue Camera Adapter V2.0C
Cable length has been shortened to improve the signal quality (from 100mm to 50mm), see known issue: HAR-4972
September 2020
 

Errata/Known issues

Errata Documents

Analogue Camera Adapter Errata

Migration in Progress

Issue trackers are not yet available in the new developer website. See it on the archived developer website.



Send Feedback!